Viega - side 46

Forlengelse- gunmetal- R-gjenge, Rp-gjenge

Easytop Ball valve- G-threadComponentsValve casing gunmetal or silicium bronze according to DIN 50930-6 / DIN EN 1982, with cylindrical G-thread in accordance with ISO 228 for flat sealing screw fittings, maintenance-free selector shaft, stainless steel ball, actuation lever T-form with medium marking green/red exchangeable.Technical dataoperating pressure max. 1.6 MPa (PN 16)operating temperature max. 110 °Cwith DVGW-test mark DN: 20, G: 1

Flow-optimised press connector system for drinking water installations in acc. with DIN 1988 and DIN 50930-6 as well as heating installations, tested in acc. with DVGW worksheet W 534.Press connectorsSafe and fast processing without calibration of the pipe ends through O-ring-free press technology in all dimensions. In this way, widening or calibration of the pipe-ends becomes superfluous and reduces the assembly times. The interaction between aerodynamic radii and minimal cross-section narrowings ensure the lowest pressure losses in press systems for multilayer pipes. This allows a smaller dimensioning of drinking water installations and reduces the pipeline volume.SC-ConturAll sizes with SC-Contur – connections, which remain unpressed become visible when the system is filled. The SC-Contur is certified and fulfils the requirements of DVGW worksheet W 534, point 12.14, connectors with forced leakage.During leakage tests with water, Viega guarantees the identification of unpressed connections in the pressure range 0.1 MPa–0.65 MPa, in the case of a dry leakage test with compressed air or noble gases from 22 hPa–0.3 MPa.MarkingGreen dot on the press connectionPipesRaxofix PE-Xc/Al/PE-Xc•dimensionally stable, oxygen-proof in acc. with DIN 4726, greyRaxofix PE-Xc•flexible, blackDimensionsPress connectors and pipes•Raxofix-PE-Xc/Al/PE-Xc: d 16/20/25/32/40/50/63•Raxofix PE-Xc: d 16/20Areas of application PE-Xc/Al/PE-XcDrinking waterHeatingRainwaterCompressed airAreas of application PE-XcRainwaterDrinking waterUse of the system for application areas other than those described here must be agreed with Viega Service Center.Operating conditionsDrinking water installations•Operating temperature max. 70 °C•Operating pressure max. 1.0 MPaHeating installations•Operating temperature max. 80 °C•Operating pressure max. 1.0 MPaIrrelevant of the direction of flow, mixed installations are permitted.NoteThe DVGW test mark is only valid f

Megapress Adapter with SC-Contur for drinking water installation- steel pipes in accordance with DIN EN 10220/10255 with galvanizing in accordance with DIN EN 10240- gunmetal or silicium bronze- press connectorsComponentsEPDM sealing element, cutting ring, separator ringDN: 25, D: 1, d: 28

Easytop Slanted seat valve (free-flow valve), with SC-Contur- press connectorsComponentsValve casing and top made of gunmetal or silicium bronze in accordance with DIN 50930-6 / DIN EN 1982, valve seat and valve plate unit stainless steel, spindle transmission, position indication open/closed, ergonomic handwheel and closed with medium marking green/red exchangeable, drain plug G14, EPDM sealing elements.Technical dataoperating pressure max. 1.6 MPa (PN 16)operating temperature max. 90 °Cwith DVGW-test markDN: 40, d: 42

T-stykke - kobber - loddeforbindelse d1: 22, d2: 28, d3: 22 (kvalitetsmerke for d12-54)

Prestabo Sliding coupling with SC-Contur - galvanised non-alloyed steel - press connectors Components EPDM sealing elementsd: 35(VdS certification)

T-piece- gunmetal or silicon bronze- Rp-threads

T-piece- gunmetal or silicon bronze- Rp-threads

Viega Extension 3525.

Nipple pipe- gunmetal- G-thread.

Viega reducing coupling 3240.

T-piece - copper - solder connection.

Adapter elbow 90° - gunmetal - soldered connection, Rp-thread.

T-piece - copper - solder connection.

Connection screw fitting- gunmetal- R-thread, G-thread- flat sealingComponentsPolygon, flat seal AFM 34

Plug-in piece - gunmetal - plug-in end, Rp-thread.

Sanpress Plug-in piece- gunmetal or silicium bronze- plug-in end, R-threadComponentsPolygon.

Sanpress Plug-in piece- gunmetal or silicium bronze- plug-in end, R-threadComponentsPolygon.

Press connector system with press connectors and pipes made of copper in acc. with EN 1057 and DVGW worksheet GW 392 suitable for:•Gases in acc. with DVGW G 260 in gas installations in acc. with DVGW-TRGI 2008 (DVGW worksheet G 600) / DVFG-TRF 2012•Liquid gas in the gas phase for domestic and commercial applications, tested in acc. with DVGW worksheet G 5614•Heating oil pipelines for heating oil in acc. with DIN 51603-1•Diesel fuel pipelines for diesel fuel, as suction and pressure pipelines in acc. with EN 590 in consideration of the general technical approval Z-38.4-71Press connectorsAll sizes with SC-Contur – connections, which remain unpressed become visible when the system is filled. The SC-Contur is certified and fulfils the requirements of DVGW worksheet G 5614, point 4.4.1, connectors with forced leakage.During leakage tests with water, Viega guarantees the identification of unpressed connections in the pressure range 0.1 MPa–0.65 MPa, in the case of a dry leakage test with compressed air or noble gases from 22 hPa–0.3 MPa.MarkingYellow dot, yellow rectangle and inscription »Gas MOP 5 / GT1«Sealing elementsHNBR, yellowDimensions/MaterialStandard sizes: d 12, 15, 18, 22, 28, 35, 42, 54 made of copperXL sizes: d 64.0 made of copperPress connectors with threaded connection d 12–54 made of gunmetalXL press connectors with threaded connection d 64.0 made of copperAreas of applicationNatural gas/Liquid gasHeating oil/Diesel fuel (d 12–54)NoteOnly Viega copper and gunmetal press connectors, which are marked with a yellow rectangle and have the inscription »Gas MOP 5 / GT1« are permitted for use in installations for gas, heating oil and diesel fuel systems!Use of the system for application areas and media other than those described here must be agreed with Viega Service Center through a material request.Operating conditionsGas and liquid gas systems•Operating temperature -20 °C up to +70 °C•Operating pressure max. 0.5 MPa•Operatin

Sanpress Inox Adapter elbow 90° with SC-Contur- steel non-corroding- press connection, Rp-threadComponentsEPDM sealing element .

T-piece - copper - solder connection.

Adapter - gunmetal - soldered connection, Rp-thread.

Plug-in piece - gunmetal - plug-in end, Rp-thread.

Viega Blok 15 mm x 1/2" with bent back pad. For solder connection, insertion dimension. 150 mm, with short redware angles, with bent holder.